CJPSS - HIGH TEMPERATURE INSULATION ADHESIVE, 760 NG

  • MSDS: CJPSS
  • Manufacturer: VIMASCO CORP
  • Product Name: HIGH TEMPERATURE INSULATION ADHESIVE, 760 NG
  • National Stock Number: 8040-00N064696
Product Identification

Product ID:HIGH TEMPERATURE INSULATION ADHESIVE, 760 NG
MSDS Date:02/19/1998
FSC:8040
NIIN:00N064696
Status Code:A
MSDS Number: CJPSS

Responsible Party
VIMASCO CORP
NITRO, WV 25143
US

Emergency Phone: 304-755-3328

Info Phone: 304-755-3328

Cage: 14947

Contractor
VIMASCO CORP
516 NITRO, WV 25143 US

Telephone: 304-755-3328

Cage: 14947

Ingredients

NOT

CAS: 1344-09-8

OSHA PEL 2 MG/M3, C

ACGIH TLV: 2 MG/M3

Hazards

LD50 LC50 Mixture:SEE INGREDIENT.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN: ON CONTINUED CONTACT, WILL CAUSE
SEVERE IRRITATION. CHRONIC LOCAL EFFECT MAY CONSIST OF SUPERFICIAL
DESTRUCTION. EYES: CAN CAUSE SEVERE IRRITATION IF NOT TREATED.
INHALATION: EXPOSURE TO MISTS M AY CAUSE COUGHING, SNEEZING; SEVERE
EXPOSURE MAY RESULT IN LUNG TISSUE DAMAGE. INGESTION: IRRITATION TO
MUCOUS MEMBRANES.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE KNOWN.

First Aid

First Aid:SKIN: WASH WITH SOAP AND WATER. EYES: FLUSH WITH CLEAN WATER
FOR AT LEAST 15 MINUTES. IF IRRITATION PERSISTS, CONSULT MD.
INHALATION: REMOVE TO FRESH AIR. IF BREATHING IS DIFFICULT,
ADMINISTER OXYGEN. IF IRRITATION PERSISTS, CONSULT MD. INGESTION:
DO NOT INDUCE VOMITING. GIVE SEVERAL GLASSES OF MILK OR WATER; SEEK
MEDICAL ATTENTION.

Fire Fighting

Flash Point Method:TCC
Flash Point:=100.C, 212.F
NO FLASH TO BOIL
Lower Limits:NOT AVAIL
Extinguishing Media:FOAM, CO*2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE KNOWN. FLAMMABILITY CLASSIFICATION:
OSHA - IIIB; DOT - NOT REGULATED.

Accidental Release

Spill Release Procedures:SPILLS WILL BE VERY SLIPPERY. FOR LARGE
SPILLS, CONTAIN LIQUID AND SHOVEL UP MATERIAL FOR REMOVAL BY VACUUM
TRUCK. NEUTRALIZE RESIDUE WITH DILUTE ACID, FLUSH AREA WITH WATER,
FOLLOWED BY LIBERAL COVER ING OF SODIUM BICARBONATE. SMALL SPILLS
ARE READILY WASHED AWAY WITH WATER.
Neutralizing Agent:NEUTRALIZE RESIDUE WITH DILUTE ACID, FLUSH AREA WITH
WATER, FOLLOWED BY LIBERAL COVERING OF SODIUM BICARBONATE.

Handling

Handling and Storage Precautions:FOR INDUSTRIAL USE ONLY. STORE INDOORS
AT TEMPERATURES OF 40F TO 90F. NOT FOR SPRAY TYPE APPLICATIONS.
PROTECT FROM FREEZING.
Other Precautions:FOR INDUSTRY/PROFESSIONAL USE ONLY. NOT INTENDED FOR
RETAIL SALE OR USE BY INDIVIDUAL CONSUMERS. DO NOT REUSE CONTAINER
FOR POTABLES OR EDIBLES. DRIED MATERIAL CAN PRODUCE VERY HARD,
SHARP EDGES. DO N OT SAND OR GRIND DRIED MATERIAL, AS RESPIRABLE
SILICA DUST CAN BE GENERATED.

Exposure Controls

Respiratory Protection:IN RESTRICTED VENTILATION AREAS, USE NIOSH
APPROVED CHEMICAL VAPOR RESPIRATOR. IN APPLICATIONS WHERE MISTS OR
SPRAY MAY BE GENERATED, AVOID INHALATION OF AIRBORNE PARTICULATES
BY USING A NIOSH APPROVE D RESPIRATOR WITH ORGANIC VAPOR CARTRIDGE
WITH PREFILTER FOR MIST OR DUST.
Ventilation:GENERAL (MECHANICAL) ROOM VENTILATION IS EXPECTED TO BE
SATISFACTORY.
Protective Gloves:RUBBER GLOVES. GLOVES MAY BE CLEANED WITH MILD SOAP &
WATER.
Eye Protection:ANSI APPROVED CHEMICAL WORKERS GOGGLES & FULL LENGTH
FACESHIELD .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
Work Hygienic Practices:THOROUGHLY CLEANSE HANDS AFTER HANDLING, AS
EXPOSURE CAN CAUSE BURNS WHICH ARE NOT IMMEDIATELY PAINFUL OR
VISIBLE. LAUNDER & DRY CLOTHING BEFORE REUSE. DISCARD FOOTWEAR THAT
CANNOT BE CLEANED.
Supplemental Safety and Health
PHYSICAL DATA: WT/GAL: 10.4 LBS.

Chemical Properties

Boiling Pt:>100.C, 212.F
B.P. Text:212F - 216F
Melt/Freeze Pt:=0.C, 32.F
Decomp Temp:=426.7C, 800.F
Decomp Text:APPROX
Vapor Pres:SEE INGREDIENT
Vapor Density:LTR/AIR
Spec Gravity:1.25
pH:11
Viscosity:APPROX 80,000 CENTIPOISE
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:APPRECIABLE
Percent Volatiles by Volume:56

Stability

Stability Indicator/Materials to Avoid:YES
THIS MATERIAL IS ALKALINE - AVOID CONTACT WITH ACIDIC MATERIALS.
Stability Condition to Avoid:NONE KNOWN.
Hazardous Decomposition Products:NONE.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Disposal

Waste Disposal Methods:DISPOSAL MUST BE I/A/W FEDERAL, STATE & LOCAL
REGULATIONS . DISPOSE OF I/A/W ALL APPLICABLE REGULATIONS. REVIEW
HAZARD SECTION OF THIS MSDS BEFORE ATTEMPTING CLEANUP. EMPTY
CONTAINERS ARE NON HA ZARDOUS UNDER RCRA AS INDUSTRIAL WASTE.

Transport

Transport Information:SHIPPING CLASS 55, PAINT (NO SPECIAL LABELS
REQUIRED).

Regulatory

SARA Title III Information:THIS MIXTURE CONTAINS THE FOLLOWING
MATERIALS REGULATED UNDER SECTION 313: NONE.
State Regulatory Information:

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.